OPW Swivel Joint Repair Parts
Description:
Seal Replacement Kits - Lubricants - Ball Bearings
Coupling Category
Swivel Joint Repair Parts
Manufacturer
OPW Engineered Systems
Seal Replacement KitsOPW Engineered Systems has kits available to rebuild all swivel joints. The kits contain all the necessary parts to replace the wear parts. Before installing new seals, care should be taken to see that all machined surfaces are clean and that there are no nicks, scratches or burrs. Consult JGB for the proper kit. |
|
Lubricants
OPW swivel joints should be lubricated periodically, depending on service and operating conditions. For normal operation, two or three times yearly is usually sufficient. Lubricating as often as once daily may be required when service is severe, such as high temperatures, heavy loads, or constant rotation. Recommendation: OPW 883 or a good Grade 2 cup grease. For EPT seals: OPW 885. For food service applications: OPW 887.
OPW 883 Lubricant
For swivel joints and similar applications. This is a general purpose industrial grease with rust and oxidation inhibitors for use with Buna-N, Viton®, PTFE and Neoprene seals. (Do not use with EPT seals.) Packaged in 14 oz. (400 grams) cartridge.
OPW 885 Lubricant
For use in OPW swivel joints and similar applications with EPT seals. 14 oz. (400 grams) cartridge.
OPW 887 Lubricant
For use in OPW swivel joints in food service applications. Approved by FDA and USDA for incidental contact with edible products. 13 oz. (370 grams) cartridge.
Ball Bearings
Both steel and stainless steel ball bearings are available for all OPW swivels. Each swivel plane of rotation has two races; quantities shown below are per pair of races.
| Size | No. Balls Per | Part No. | Part No. |
| Pair of Races | Steel Balls | Stainless Balls | |
| 3/4" & 1" | 40 | H-7063-M1 | H-30035-M |
| 1 1/4" & 1 1/2" | 56 | H-7063-M1 | H-30035-M |
| 2" | 48 | H-6712-M2 | H-1171-M |
| 3" | 66 | H-6712-M | H-1171-M |
| 4" | 84 | H-6712-M | H-1171-M |
| 6" | 76 | H-6780-M | H-30036-M |
| 8" | 98 | H-6780-M | H-30036-M |
| 10" | 98 | H-30162-M | H-30147-M |
1 3200 Series swivels use H-4577-M balls.
2 3200 Series swivels use H-4576-M balls.
Flange Dimensions
| Type | Size | Flange O.D. | Bolt Circle | No. Bolt | Bolt Dia. | |||
| in. | (mm) | in. | (mm) | Holes | in. | (mm) | ||
| 150 lb. ASME | 2" | 6 | (153) | 4 3/4 | (121) | 4 | 5/8 | (16) |
| 150 lb. ASME | 3" | 7 1/2 | (191) | 6 | (153) | 4 | 5/8 | (16) |
| TTMA | 3" | 5 5/8 | (143) | 4 7/8 | (124) | 8 | 3/8 | (10) |
| 150 lb. ASME | 4" | 9 | (229) | 7 1/2 | (191) | 8 | 5/8 | (16) |
| TTMA | 4" | 6 5/8 | (169) | 5 7/8 | (150) | 8 | 3/8 | (10) |
| 150 lb. ASME | 6" | 11 | (280) | 9 1/2 | (150) | 8 | 3/4 | (19) |
| 150 lb. ASME | 8" | 13 1/2 | (343) | 11 3/4 | (242) | 8 | 3/4 | (19) |
| 150 lb. ASME | 10" | 16 | (407) | 17 | (432) | 12 | 7/8 | (22) |
Note: 300 lb., 600 lb., other types of flanges available on special order. Consult JGB.
 |
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov |