Vendor: Parker Industrial

Category: Petroleum Hose    Sub Type: Petroleum Dispensing Hose

---

Application:

X-TREME™
Low Temperature LP Gas Hose
UL21, CGA Type I
Series 7132XTC

• LP gas/propane
• Low temperature delivery, transfer
• Agriculture, commercial and residential heating, construction, general industrial

Series 7132XTC is a flexible, lightweight, low temperature liquefied petroleum gas (LPG)/propane delivery and transfer hose. The hose meets all Underwriters Laboratories (UL21) and Canadian Gas Association (CGA Type I) requirements. The construction stays flexible to -65°F (-53°C) and incorporates multiple textile plies of reinforcement for flexibility and kink resistance. The perforated cover is resistant to mild chemicals, oil and ozone. Series 7132XTC is available in long lengths on reels, long cut lengths and factory-tested assemblies from stock in popular configurations.

Series 7132XTC and DOT: LPG hose assemblies installed on on-road vehicles must meet Department of Transportation (DOT) requirements. Factory assemblies (3/4" and larger) are pressure tested, one of the fittings is etched with a unique DOT certification number, and a document incorporating the identical certification number accompanies each shipment. Metal DOT identification bands are also attached at an additional charge per customer request. Contact JGB.

Series 7132XTC and Natural Gas: The molecules of natural gas are small, enhancing their ability to permeate through standard rubber hose constructions. The permeation process is more rapid as the working pressure increases, and natural gas accumulates with potentially dangerous consequences. Series 7132XTC may be used for natural gas service, but ONLY under ALL of the following conditions:

• The application must be in a well-ventilated environment: Outdoors, or indoors with significant continuous air movement.
• Series 7132XTC is not to replace fixed/rigid pipe where that material is more appropriate due to reduced permeation and overall strength and durability. Use rigid pipe, non-permeable tubing or hose with barrier constructions to convey natural gas whenever possible.

Series 7132XTC and Compressed Natural Gas (CNG): Series 7132XTC is not for use in any CNG application, including fuel dispensing, on-board vehicle fuel lines, or fuel transfer.

Series 7132XTC and Anhydrous Ammonia (NH3): Series 7132XTC is not for use with anhydrous ammonia.

Design Factor:  5:1
Vacuum:  Not recommended
Industry Standards:  UL21; CAN/CGA-8.1-M86 Type I; optional DOT factory hose assembly testing and marking also available for sizes smaller than 3/4

Tube:

Black Nitrile

Reinforcement:

Multiple textile plies

Cover:

Black chloroprene; perforated smooth finish

Temperature:

-65°F to +180°F (-53°C to +82°C)
(The hose construction is capable of this rating, but LP Gas should NEVER be conveyed over 140°F/60°C)

Packaging:

Cartons, coils, reels

Branding:

PARKER SERIES 7132XTC X-TREME CGA TYPE I CAUTION - LP GAS HOSE (-65°F) MH6737 C U ® US ISSUE NO. XXXXX 350 PSI MAX WP MADE IN USA B2 (DATE CODE)

Couplings:

Contact JGB for proper fitting recommendation and coupling procedure.

Colors:

Black

Options:

Metal DOT identification bands

Part Number	ID	ID	Reinf Plies	OD	OD	Approx Wt	Min Bend Rad	Max Rec WP	Std Pack	Request Quote
	(in)	(mm)		(in)	(mm)	(lbs/ft)	(in)	(psi)	Qty (ft)
7132XTC-1000	1	25.4	4	1.5	38.1	0.63	7.5	350	250	Request Quote
7132XTC-1000100	1	25.4	4	1.5	38.1	0.63	7.5	350	1 x 100	Request Quote
7132XTC-1000125	1	25.4	4	1.5	38.1	0.63	7.5	350	1 x 125	Request Quote
7132XTC-1000150	1	25.4	4	1.5	38.1	0.63	7.5	350	1 x 150	Request Quote
7132XTC-25354	1/4	6.4	4	0.61	15.5	0.14	2.5	350	750	Request Quote
7132XTC-38354	3/8	9.5	4	0.76	19.3	0.21	3.5	350	650	Request Quote
7132XTC-50354	1/2	12.7	4	0.937	23.8	0.3	4.5	350	500	Request Quote
7132XTC-75354	3/4	19.1	4	1.25	31.8	0.48	6.5	350	350	Request Quote

WARNINGS! Use only with couplings qualified by Parker. Do not use with male swivel couplings or other couplings containing o-rings, which may dry out, crack and fail over time. When using this product in a mobile application such as delivery or service vehicles, the inspection procedures detailed in DOT regulation 49CFR 180.416 must be strictly adhered to.

---