Drillsite Support Hoses

Eagle Air® Brass Coated Steel Wire Reinforced Hose is Long-lasting, heavy-duty air hose with wire reinforcement for use in mines, construction and industrial applications where maximum service is required. It is ozone and abrasion resistant hose, and features a high degree of safety against bursting. It has a working pressure of 600 PSI and a burst pressure of 2400 psi.
2", 3", 4", and 6" ID

Eagle EPDM 270 PSI Steam Hose - is a heat resistant hose designed for the transfer of saturated and superheated steam in shipyards, chemical plants and industrial applications. It is reinforced with high tensile steel braids for strength. It comes with a pin-pricked red EPDM cover to allow for venting. 1/2" to 2" ID -40°F to +410°F (Intermittent 450°F)

For low to medium pressure hydraulic systems in industry and agriculture. The synthetic rubber tube is resistant to hydraulic fluids, and the MSHA approved synthetic rubber cover is abrasion and ozone resistant. Various covers are available for this hose.
1/4" to 1" ID
-40°F to 212°F (max 248° intermittent)

The J-FLEX® 10K Hydraulic Jack Hose features a burst pressure of 20,000 psi and is reinforced with 2 braids of high tensile steel wire. It has a MSHA, abrasion and weather resistant synthetic rubber cover. The tube is oil resistant.
1/2" and 3/8" ID
-40°F to 212°F (depending on the medium)

Reinforced with four high tensile steel spirals, this hose is designed for hydraulic systems with high peak pressures and arduous operating conditions. The special synthetic cover is designed to resist hydraulic oil, weather, and abrasion. The synthetic rubber tube is resistant to mineral, vegetable, and glycol based hydraulic oils. A MSHA cover is available.
3/8" to 2" ID
-40°F to 248°F (257°F intermittent)

This hose comes reinforced with 4 or 6 high tensile steel spirals and has a working pressure of 5000 psi and a burst pressure of 20000 psi. This hose is designed for hydraulic systems with high peak pressures and arduous operating conditions.
3/4" to 2" ID
-40°F to 250°F

This hose is compatible with biodegradable hydraulic fluids like vegetable oil as well as mineral and glycol based hydraulic fluids. It consists of an inner tube of oil-resistant special synthetic rubber, 4 or 6 spiral plies of heavy wire wrapped in nating directions, and an oil, abrasion, and weather-resistant special rubber cover.
3/4" to 1-1/2" ID
-40°F to 250°F

This hose is rated for 3000 PSI in all sizes. It is for use in medium pressure hydraulic systems in industry and agriculture. The tube is resistant to hydraulic fluids and is reinforced with one two braids of high tensile steel wire. The cover is abrasion and ozone resistant synthetic rubber. Various covers are available including MSHA.
1/4" to 1" ID
-40°F to 212°F (248°F discontinuous)

For medium to high pressure hydraulic systems in industry and agriculture. The synthetic rubber tube is resistant to hydraulic fluids, and the MSHA approved synthetic rubber cover is abrasion and ozone resistant. Various covers are available for this hose.
1/4" to 1" ID
-40°F to +212°F (max 248° intermittent)

J-FLEX® HOT OIL 2SN Hose - is specially formulated as a high temperature hose. It has an oil resistant synthetic rubber cover that is also weather and abrasion resistant. This hose is reinforced with two high tensile steel braids for strength.
1-1/2" ID
-40°F to 275°F ( 300°F intermittent)

High Pressure service needing abrasion resistance, tight bends and flexible. For petroleum and water based hydraulic fluids. Excellent impulse performance and flexibility exceeding SAE 100R2 and SAE 100R16 standards.